Corflute Roll

product_banner
2mm Corflute Rolls Corrugated Plastic Sheet
heavy duty floor protector sheet wholesale
2mm Corflute Rolls Corrugated Plastic Sheet
custom floor protector pp corrugated sheet
2mm Corflute Rolls Corrugated Plastic Sheet
recyclable pp construction floor covering
2mm Corflute Rolls Corrugated Plastic Sheet
heavy duty floor protector sheet wholesale
2mm Corflute Rolls Corrugated Plastic Sheet
custom floor protector pp corrugated sheet
2mm Corflute Rolls Corrugated Plastic Sheet
recyclable pp construction floor covering
Corflute Roll
Description:

✓ 2 mm PP corrugated board in rolls

✓ Widths to 1220 mm, lengths to order

✓ Floor, wall, window and stair protection

✓ Covers waterproofing membranes during works

✓ Printed-logo option turns it into site branding

✓ 200 rolls MOQ, cut and slit to spec

product details

A corflute (correx) protection roll is 2 mm corrugated polypropylene board wound into a roll: unroll it over finished floors, membranes and surfaces during construction, tape the joints, and at handover pull it up in sheets — the surface underneath is exactly as it was at installation. Unlike cardboard underlay, it takes a week of rain through an open doorway without turning to pulp, and unlike plastic sheeting it does not slide underfoot or trap moisture against fresh screed.

2mm corflute rolls corrugated plastic sheet

➤What It Protects, and How

Finished floors. Tiles, timber, epoxy and engineered boards get damaged by traffic, dropped tools and trolley wheels during the busiest phase of a project — fit-out. A 2 mm roll absorbs that traffic; a 3 mm roll takes trades plus trolleys and light plant. The fluted surface also gives grip where smooth plastic sheeting is a slip hazard.

Waterproofing membranes. Basement walls, podium slabs, planters and decking membranes are damaged by backfill and follow-on trades after the membrane is applied and inspected. Corflute is the standard sacrificial layer between membrane and works — it takes the impact so the membrane does not, and it does not bleed or retain water against the surface it protects.

Walls, windows and stairs. The same roll slit to narrower widths lines corridors, guards glazing and covers stair nosings. Because it is board rather than film, it survives bumping rather than just covering.

Printed rolls. Many main contractors specify a printed logo band — the protection becomes site branding and, more practically, makes off-cuts instantly identifiable as the contractor's material. Print runs at the same lead time as plain rolls.

2mm corflute protection roll unrolled on site

▤Choosing the Specification

Thickness first. 2 mm for foot traffic and membrane protection; 3 mm where trolleys, trades and heavy boots cross it daily. The honest limit: corflute is temporary protection, not a working surface — scissor lifts and steel-toed plant need 3 mm plus taped joints, or a different product.

Width and length. Rolls run to 1220 mm wide and 20–50 m long; narrower widths are slit from the master roll, which is why odd widths (stair treads, window reveals) cost no premium at MOQ. Seaming: overlap joints 50–100 mm and tape seams plus perimeter edges with a low-residue tape — the tape, not the roll, is what leaves marks if chosen badly, so ask us for the compatible one.

2mm corflute rolls stocked in the warehouse

✔How We Produce and Check Each Batch

Board is extruded on our own lines and slit, wound and trimmed in the same plant, so thickness is controlled at extrusion and edge quality is checked per roll. Printed bands are proofed against artwork before the run, and rolls are palletised and bundled per width so site crews can pull exactly what the floor plan needs. Specs stay on file — repeat site orders quote against a reference.

➤Sequencing Protection with the Programme

Surface protection fails more often from poor sequencing than from thin board. The roll goes down when the surface it protects is finished — screed cured, epoxy flash-off complete, grout set — not before; protecting a wet surface traps moisture and prints the tape pattern into it. Plan each area's roll install against the trade programme: floors protected as fit-out starts, corridors as traffic shifts, membranes the day after inspection and before backfill.

Handover is the other half of the plan. Lift the roll in sheets — it comes up whole because the boards are taped at seams only — stack the used sheets flat and they leave site as clean recyclable PP, not torn cardboard mixed with rubble. Main contractors who specify printed rolls usually add the logo band for exactly this phase: at handover walkthroughs, protected floors still carrying the contractor's brand photograph well, and the difference between "protected" and "clean" is often the difference in the final payment application.

ℹAbout the Manufacturer

Qingdao Hengsheng Plastic Co., Ltd. has extruded PP corrugated board in Qingdao since 2012. Four lines give a capacity of 20,000 tons a year, and rolls are slit and wound in the same plant. We ship to more than 120 countries, with protection rolls going mainly to main contractors, waterproofing applicators and rental companies in Europe, Australia and North America.

Written by the Hengsheng technical sales team, Qingdao · Last updated: November 2026

Further Reading

Corflute RollProtection RollCorrex

Product parameters

MaterialPP (polypropylene) corrugated board, 100% recyclable
Thickness2 mm standard; 3 mm for heavy traffic
Roll widthUp to 1220 mm; slit to narrower widths
Roll length20–50 m standard; custom to order
ColourWhite, black, grey; printed logo option
ApplicationsFloors, walls, windows, stairs, membranes, planters, podium slabs
InstallUnroll, overlap joints, tape seams and edges
Traffic classLight–medium foot traffic; 3 mm for trades plus trolleys
ReuseSingle project typical; thicker grades re-usable on site
MoistureZero uptake — no bleed onto fresh screed
PackingPalletised rolls, bundled per width
MOQ200 rolls per specification
Delivery7–10 days after T/T deposit

faq

  • Q: Are you a factory or a trading company?

    A: We are the manufacturer. Four PP corrugated board extrusion lines in Qingdao give a capacity of 20,000 tons per year, and the rolls are slit and wound in the same plant.

  • Q: What thickness should I use?

    A: 2 mm for foot traffic and membrane protection; 3 mm where trolleys and trades cross daily. Corflute is temporary protection, not a working surface.

  • Q: Can it protect waterproofing membranes?

    A: Yes - basement walls, podium slabs, planters and decking. It is the standard sacrificial layer between the membrane and backfill or follow-on trades.

  • Q: Will it mark fresh screed or epoxy?

    A: The board itself does not bleed or trap moisture. What leaves marks is the wrong seam tape - use a low-residue tape and ask us for the compatible type.

  • Q: What widths and lengths are available?

    A: Up to 1220 mm wide, 20-50 m standard lengths; narrower widths are slit from the master roll, so odd widths cost no premium at MOQ.

  • Q: Can we get printed logo rolls?

    A: Yes - a printed logo band runs at the same lead time as plain rolls, and doubles as site branding and material identification.

  • Q: How is it installed?

    A: Unroll, overlap joints 50-100 mm, tape the seams and perimeter edges. At handover it lifts in sheets and can be recycled.

  • Q: What is the MOQ and lead time?

    A: 200 rolls per specification; T/T deposit standard and production takes 7-10 days after deposit.

inquire now

Product Evaluation

WRITE A REVIEW

  • Rating:

We Offer You 100% Custom-Made Service

8618661437117

0086-18661437117

amy@qdhsplastic.cn

2546ba282d566414120b048cd876e3d